View LB11693JH10_2983690.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

specifications of any and all sanyo semiconductor co.,l td. products described or contained herein stipulate the performance, characteristics, and functions of the described products in the independent state, and are not guarantees of the performance, characteristics, and functions of the described products as mounted in the customer ' s products or equipment. to verify symptoms and states that cannot be evaluated in an independent device, the customer should always evaluate and test devices mounted in the customer ' sproductsor equipment. any and all sanyo semiconductor co.,ltd. products described or contained herein are, with regard to "standard application", intended for the use as general el ectronics equipment (home appliances, av equipment, communication device, office equipment, industrial equ ipment etc.). the products mentioned herein shall not be intended for use for any "special application" (medica l equipment whose purpose is to sustain life, aerospace instrument, nuclear control device, burning appliances, t ransportation machine, traffic signal system, safety equipment etc.) that shall require extremely high level of re liability and can directly threaten human lives in case of failure or malfunction of the product or may cause har m to human bodies, nor shall they grant any guarantee thereof. if you should intend to use our products for app lications outside the standard applications of our customer who is considering such use and/or outside the scope of our intended standard applications, please consult with us prior to the intended use. if there is n o consultation or inquiry before the intended use, our customer shall be solely responsible for the use. 90110 sy 20100827-s00001 / d1306 ms im 20060404-s00004 no.a0606-1/12 lb11693jh overview the lb11693jh is a three-phase brushless motor driver ic that uses a direct pwm drive technique to achieve highly efficient drive. it is optimal for driving fu el pump motors and other miniature motors. functions ? soft phase switching + direct pwm drive ? pwm control based on both a dc voltage input (the ctl voltage) and a pulse input ? provides a 5v regulator output ? one hall-effect sensor fg output ? built-in integrating amplifier ? automatic recovery constraint protection circuit (on/off = 1/14), rd output ? built-in current limiter circuit ? built-in lvsd circuit ? built-in thermal protection circuit specifications absolute maximum ratings at ta = 25 c parameter symbol conditions ratings unit supply voltage range v cc max 30 v output current i o max t 500ms 1.8 a allowable power dissipation 1 pd max1 independent ic 0.9 w allowable power dissipation 2 pd max2 mounted on a specified board* 2.1 w operating temperature topr -40 to +85 c storage temperature tstg -55 to +150 c * mounted on a specified board: 114.3mm 76.1mm 1.6mm, glass epoxy ordering number : ena0606a monolithic digital ic 24v fan motor driver ic
lb11693jh no.a0606-2/12 allowable operating ranges at ta = 25 c parameter symbol conditions ratings unit supply voltage range v cc 8 to 28 v constant voltage output current ireg 0 to -30 ma rd output current ird 0 to 10 ma fg output current ifg 0 to 10 ma electrical characteristics at ta = 25 c, v cc = vm = 24v ratings parameter symbol conditions min typ max unit current drain 1 i cc 1 10 13.5 ma current drain 2 i cc 2 when stop 4.0 5.5 ma [output block] output saturation voltage 1 v o sat1 i o = 0.7a,v o (sink)+v o (source) 1.5 2.05 v output saturation voltage 2 v o sat2 i o = 1.5a,v o (sink)+v o (source) 2.2 2.9 v output leakage current i o leak 100 a high side diode forward voltage 1 v d 1 i d = 0.7a 1.25 1.65 v high side diode forward voltage 2 v d 2 i d = 1.5a 1.9 2.5 v [5v constant voltage output] output voltage vreg i o = -5ma 4.7 5.0 5.3 v line regulation vreg1 v cc = 9.5 to 28v 30 100 mv load regulation vreg2 i o = -5 to -20ma 20 100 mv [hall amplifier] input bias current ib(ha) 2 10 a hall sensor input sensitivity vhin sine wave input 50 350 mvp-p common-mode input voltage range vicm differential input 50mvp-p 1.5 vreg-1.0 v input offset voltage vioh design target value* -20 +20 mv [csd pin] high-level output voltage v oh (csd) 2.75 3.0 3.25 v low-level output voltage v ol (csd) 0.85 1.0 1.15 v external capacitor charge current icsd1 -3.3 -2.4 -1.4 a external capacitor discharge current icsd2 0.09 0.17 0.23 a charge/discharge current ratio rcsd charge current/discharge current 14 times [undervoltage protection circuit (lvs pin)] operating voltage vsdl 3.6 3.8 4.0 v release voltage vsdh 4.1 4.3 4.5 v hysteresis vsd 0.35 0.5 0.65 v [current limiter circuit] limiter voltage vrf v cc -vm 0.45 0.5 0.55 v [thermal shutdown operation] thermal shutdown operating temperature tsd design target value* (junction temperature) 150 170 c hysteresis tsd design target value* (junction temperature) 40 c [ctl amplifier] input offset voltage vio(ctl) -10 10 mv input bias current ib(ctl) -1 1 a common-mode input voltage range vicm 0 vreg-1.7 v high-level output voltage v oh (ctl) itoc = -0.2ma vreg-1.2 vreg-0.8 v low-level output voltage v ol (ctl) itoc = 0.2ma 0.8 1.05 v open-loop gain g(ctl) f(ctl) = 1khz 45 51 db *: design target value and no measurement was made. continued on next page.
lb11693jh no.a0606-3/12 continued from preceding page. ratings parameter symbol conditions min typ max unit [pwm oscillator circuit] high-level output voltage v oh (pwm) 2.75 3.0 3.25 v low-level output voltage v ol (pwm) 1.1 1.3 1.4 v amplitude v(pwm) 1.5 1.7 2.0 vp-p external capacitor charge current ichg vpwm = 2.1v -125 -90 -70 a oscillator frequency f(pwm) c = 2200pf 15.5 19.5 27.0 khz [toc pin] input voltage 1 vtoc1 output duty: 100% 2.72 3.0 3.30 v input voltage 2 vtoc2 output duty: 0% 1.07 1.3 1.45 v input voltage 1l vtoc1l design target value*. 100% when vreg = 4.7v 2.72 2.80 2.90 v input voltage 2l vtoc2l design target value*. 0% when vreg = 4.7v 1.07 1.17 1.27 v input voltage 1h vtoc1h design target value*. 100% when vreg = 5.3v 3.08 3.20 3.30 v input voltage 2h vtoc2h design target value*. 0% when vreg = 5.3v 1.21 1.33 1.45 v [rd pin] low-level output voltage v ol (rd) ird = 5ma 0.1 0.3 v output leakage current il(rd) vrd = 28v 10 a [fg pin] low-level output voltage v ol (fg) ifg = 5ma 0.1 0.3 v output leakage current il(fg) vfg = 28v 10 a [fgfil pin] charge current ifgfil1 -7 -5 -3 a discharge current ifgfil2 35 7 a [fg amplifier schmitt block (in1)] amplifier gain g(fg) design target value*. 7 times hysteresis v is (fg) design target value*. input equivalent 8 mv [s/s pin] high-level input voltage v ih (ss) 2.0 vreg v low-level input voltage v il (ss) 0 1.0v input open voltage v io (ss) 2.6 2.9 3.2 v hysteresis v is (ss) 0.16 0.25 0.34 v high-level input current i ih (ss) vs/s = vreg 100 130 a low-level input current i il (ss) vs/s = 0v -170 -130 a [pwmin pin] input frequency range f(pi) 50 khz high-level input voltage range v ih (pi) 2.0 vreg v low-level input voltage range v il (pi) 0 1.0v input open voltage v io (pi) 2.6 2.9 3.2 v hysteresis v is (pi) 0.16 0.25 0.34 v high-level input current i ih (pi) vpwmin = vreg 100 130 a low-level input current i il (pi) vpwmin = 0v -170 -130 a [f/r pin] high-level input voltage v ih (fr) 2.0 vreg v low-level input voltage v il (fr) 0 1.0v input open voltage v io (fr) vreg-0.5 vreg v hysteresis v is (fr) 0.16 0.25 0.34 v high-level input current i ih (fr) vf/r = vreg -10 0 10 a low-level input current i il (fr) vf/r = 0v -165 -115 a *: design target value and no measurement was made.
lb11693jh no.a0606-4/12 package dimensions unit : mm (typ) 3251 truth table f/r = ?l? f/r = ?h? source sink in1 in2 in3 in1 in2 in3 1 out2 out1 h l h l h l 2 out3 out1 h l l l h h 3 out3 out2 h h l l l h 4 out1 out2 l h l h l h 5 out1 out3 l h h h l l 6 out2 out3 l l h h h l pin assignment -40 -20 0 20 40 60 80 1.09 0.47 100 pd max - ta ilb01760 0.4 0 0.8 0.9 1.2 1.6 2.0 2.1 2.4 mounted on a specified board: 114.3mm 76.1mm 1.6mm glass epoxy ambient temperature, ta - c allowable power dissipation, pd max - w independent ic sanyo : hsop36r(375mil) (6.2) 36 1 19 18 0.8 2.0 17.8 0.3 (4.9) 2.7 0.65 0.25 (0.5) 7.9 10.5 (2.25) 2.45max 0.1 top view 35 34 33 32 31 30 29 28 36 27 26 25 24 23 22 21 20 19 fgfil lvs vreg rd fg csd fc pwmin 10 11 12 13 14 15 16 17 18 ei- frame ei+ gnd1 s/s frame 9 8 7 6 5 4 3 2 1 in2- in2+ in1- in1+ out1 nc in3- in3+ out2 nc f/r nc pwm toc nc nc gnd2 nc nc out3 vm v cc vd nc
lb11693jh no.a0606-5/12 block diagram pin functions pin no. symbol pin description equivalent circuit 34 36 2 out1 out2 out3 motor drive output 4 gnd2 motor drive output system ground 7 vd low side output transistor drive current supply 9 vm motor drive output power supply and output current detection. connect a resistor (rf) between this pin and v cc . the output current is limited to a value determined by the equation i out = vrf/rf. 8 v cc power supply (systems other than the motor drive output) 10 vreg 5v regulator output connect a capacitor (about 0. 1f) between this pin and ground for stabilization. continued on next page. 2 34 36 300
lb11693jh no.a0606-6/12 continued from preceding page. pin no. symbol pin description equivalent circuit 11 lvs undervoltage protection voltage detection. connect this pin to vreg if the vreg level is to be detected. if the v cc level is to be detected, insert a zener diode in series to set the detection level. 12 fgfil fg filter. normally, this ic will be used with this pin open. connect a capacitor between this pin and ground if noise on the fg signal becomes a problem. 14 fc control loop frequency characteristics correction. connect a capacitor between this pin and ground. 15 csd constraint protection circuit operating time setting. 16 fg one hall-effect sensor fg output. (this is an open-collector output.) continued on next page. vreg 9.5k 52k 11 vreg 300 12 14 vreg 300 vreg 300 15 vreg 16
lb11693jh no.a0606-7/12 continued from preceding page. pin no. symbol pin description equivalent circuit 17 rd motor constrained state detection output (this is an open-collector output.) when the motor is constrained: high, when the motor is turning: low. 18 pwm in pwm pulse input. when low the output will be on and when high the outputs will be off. if this pin is used to control this ic, connect ei- to ground and connect ei+ to toc. 20 s/s start/stop control. low: start, high or open: stop. 21 22 ei+ ei- ctl amplifier noninverting input ctl amplifier inverting input 23 toc pwm waveform comparator (ctl amplifier output) continued on next page. vreg 17 vreg 30k 5k 18 40k vreg 30k 5k vreg 300 22 300
lb11693jh no.a0606-8/12 continued from preceding page. pin no. symbol pin description equivalent circuit 25 pwm pwm oscillator frequency setting. connect a capacitor between this pin and ground. a frequency of about 20khz can be set by using a 2200pf capacitor. 26 gnd1 ground (for circuits other than t he motor drive output system) 28 27 30 29 32 31 in1+ in1- in2+ in2- in3+ in3- hall effect sensor inputs high when in+ > in-, low for the reverse state. signal inputs with an amplitude (differential) of at least 50mvp-p are desirable for the hall inputs. if noise is a problem, connect capacitors between the in+ and in- inputs. 33 f/r forward/reverse control low: forward, high or open: reverse. 1,3 5,6 13,19 24,35 nc no connection. the nc pins may be used for wiring connections. frame frame connection the frame pin is connected inte rnally to the ic surface metal parts. both must be used in the electrically open state. vreg 2k 200 25 vreg 40k 3.5k 33 vreg 300 28 300
lb11693jh no.a0606-9/12 lb11693jh overview 1. output drive circuit the lb11693jh reduces motor vibration and noise by switching the output current smoothly when switching phases. since the hall input waveform is used for the change in (slope of) the output current during phase switching, if the slope of the hall input waveform is too steep, the change in the output current during phase switching will also be too steep and the effectiveness of this technique at lowering vi bration and noise effect will be reduced. thus the slope of the hall input waveform requires attention during application design. low side output transistor pwm switching is used for motor speed control. the drive output is adjusted by changing the duty. the diodes between the outputs and vm used for the regenerative current when the pwm signal is in the off state are built in. if the slope (amplitude) of the hall input waveform is large, and if used with a high current, the parasitic diodes between the outputs and ground will operate due to the low side kickback during phase switching. if problems such as disruption of the waveforms occur, connect either rectifying diodes or schottky diodes between the outputs and ground. 2. power supply stabilization since the lb11693jh uses a control method based on pw m switching, the power supply lines are susceptible to disruption. electrolytic capacitors with an adequate capacitance for stabilization must be connected between v cc and ground. if diodes are inserted in the power supply lin es to prevent destruction of the equipment if the power supply is connected in reverse, the powe r supply lines will be particularly susceptible to disruption. in this case, even larger capacitors must be used. the connected electrolytic cap acitors must be located as close as possible to the ic pins (v cc , vm, and gnd2). if the electrolytic capacitors cannot be attached close to the pins due to problems with the heat sink or other issues, ceramic capacitors of about 0.1f must be attached close to the pins. 3. vreg pin at the same time as being the 5v regulator output, the vreg pin is also the power supply for the ic internal control circuits. therefore, a capacitor of at least 0.1f must be connected between the vreg pin and ground to stabilize the control circuit power supply. the ground side of the connec ted capacitor must be connected to the gnd1 pin with as short a line as possible. 4. fc pin the capacitor connected to the fc pi n is required to correct the contro l loop's frequency characteristics. (it should be about 0.1 f.) 5. vd pin the vd pin supplies the low side output transistor drive current (a maximum of about 0.1a). the ic internal power consumption is suppressed by connecting a resistor between the v cc and vd pins and dividing power consumption due to the low side output transistor drive current with that resistor. although the ic internal power consumption due to the drive current can be reduced by lowering the vd pin voltage, a voltage of at least 4v must be assured at the vd pin. use a resistor in the range from about 50 (0.5w) to about 100 (1w) between the v cc and vd pins when the lb11693jh is used with v cc = 24v. 6. hall effect sensor input signals signal inputs with an amplitude (differential) of at l east 50mvp-p are required for the hall inputs. if the output waveforms are disrupted by noise, capacitors must be connected between the hall input pins (the + and - sides). 7. current limiter circuit the current limiter circuit limits the peak value of the out put current to a current determined by the equation i = vrf/rf (where vrf = 0.5v (typical), rf = current detection resistor value). when the limiter operates, it suppresses the current by pwm control of the low side output transi stor at the pwm frequency de termined by the external capacitor connected to the pw m pin, in particular, by reducing the on duty.
lb11693jh no.a0606-10/12 8. forward/reverse switching the lb11693jh was designed assuming that forward/reverse switching would not be performed while the motor is operating. we recommend that the f/r pin be held fixed at either the low (forward) or high (reverse) level when the motor is turning. although it will be pulled up to the high level by an internal pull-up resistor (about 40k ) when left open, this must be strengthened by an external resistor if fluctuations are large. if the direction is switched while the motor is turning, la rge currents will flow due to the braking operation. the lb11693jh's current limiter circuit, however, cannot limit th is braking current. therefor e, forward/reverse switching during motor rotation is only possible if the braking current is limited to a value under i o max (1.8a) by the motor coil resistance or other circuit or pheno menon. furthermore, since through current will flow in the high and low side transistors at the instant the switch occurs with switching that only uses the f/r pin, applications must provide a rive off period for switching directions. a drive off period must be provided by either setting the ic to the stopped state with the s/s pin or setting the pwm signal to the 0% duty state with the toc and pwmin pins, and the f/r pin must only be switched during that period to prevent through current. 9. power saving circuit this ic can be set to a power saving state in which current consumption is reduced by setting it to the stopped state with the s/s pin. the bias current to most of the circuits in the ic is cut off in this power saving state. note, however, that the 5v regulator output is still provided in the power saving state. 10. notes on the pwm frequency the pwm frequency is determined by the capacitance (f) of the cap acitor connected to the pwm pin. fpwm 1/ (23400 c) a frequency in the range 15 to 25khz is desirable for the pwm frequency. the ground side of the connected capacitor must be connected to the gnd1 pin by as short a line as possible. 11. control methods the output duty can be controlled by either of the following methods. ? comparison of the toc pin voltage with the pwm oscillator waveform this method determines the low side output transistor duty according to the result of comparing the toc pin voltage with the pwm oscillator waveform. the pwm duty will be 0% when the toc pin voltage is under about 1.3v and will be 100% when that voltage is over about 3.0v. since the toc pin is the output of the ctl amplifier, a control voltage cannot be directly input to the toc pin. accordingly, the ctl amplifier is nor mally used as a full feedback amplif ier (by connecting the ei- pin to the toc pin) and inputting a dc voltage to the ei pin (here the toc voltage will be equal to the ei+ pin voltage). when the ei+ pin voltage increases, the output duty will in crease as well. since the moto r will be driven if the ei+ pin is in the open state, a pull-down resistor should be connected to the ei+ pin in applications where this is not desirable. a low level must be input to the pwmin pin (or it must be connected to ground) if the toc pin voltage control system is used. ? pwmin pulse input a 15 to 25khz frequency pulse signal can be input to th e pwmin pin and the low side output transistor duty can be controlled based on the duty of that input signal. when the pwmin pin is low, the output will be on, and when high, the output will be off. when the pwmin pin is open, the input will go to the high level and the output will be off. if pwmin pin control is used, the ei- pin must be connected to ground and the ei+ pin must be connected to the toc pin.
lb11693jh no.a0606-11/12 12. undervoltage protection circuit the undervoltage protection circuit turns off the low side output transistor if the lvs pin voltage falls below the circ uit's operating voltage (about 3.8v). this operating voltage is the detection level for a 5v system. the detection level can be increased by connecting a zener diode in series with the lvs pin to apply a level shift to the detection level. the current flowing into the lvs pin during detection is about 65a. to suppress variations in the zener voltage, it is necessary to stabilize the rise of the zener diode voltage by increasing the current that flows in the zener diode. if this is necessary, insert a resistor between the lvs pin and ground. when the lvs pin is open, it will be pulled to the ground level by the built-in pull-down resistor and the output will be turned off. thus if the undervoltage protection circuit is not used, a voltage in excess of the release voltage (about 4.3v) must be applied to the lvs pin. note that the maximum rating for the lvs pin voltage is 30v. 13. motor constraint protection circuit when motor motion is constrained, the external capacitor connected to the csd pin will be alternately charged (up to about 3.0v) with a constant current of about 2.4a and discharged with a constant current of about 0.17a (to about 1.0v). thus the csd pin voltage will have a sawtooth waveform. the motor constraint protection circuit turns the motor (the low side output transistor) on or off repeatedly based on this sawtooth waveform. motor drive will be on during the period the csd pin external capacitor is bein g charged from about 1.0v to about 3.0v and will be off when it is being discharged from about 3.0v to about 1.0v. the drive on/off operation protects the ic and the motor when the motor is physically constrained from moving. if a 0.47f capacitor is connected to the csd pin, the ic will iterate an on/off cycle in which drive is on for about 0.4 seconds and off for about 5.5 seconds. while the motor is turning, the csd pin voltage will be held at a certain voltage (that depends on the motor speed) by (a) a csd pin external capacitor discharge operation based on about 10s discharge pulses generated internally in the ic when the hall input in1 switches (that is, on rising and falling edges on the fg output) and (b) a charge operation on that capacitor by a consta nt current of about 2.4a. since the hall input in1 does not switch when the motor is physically constrained, th e discharge pulses are not generated and the csd pin external capacitor will be charged to about 3.0v by the constant current of about 2.4a. the motor constraint protection circuit operates when the capacitor reaches about 3.0v. the constraint protection operation will be released when the motor constraint is released. if the motor speed is extremely low, the csd pin voltage during that motor rotation will be held at a comparatively high voltage, and if that voltage r eaches about 3.0v, the cons traint protection functio n will operate. since the constraint protection function will operate if the hall input in1 frequency falls below abou t 10hz, caution is required when using the motor constraint protection circuit with motors that will operate at low speeds. connect the csd pin to ground if the motor constraint protection circuit is not used. to the lvs pin to the detected power supply
lb11693jh no.a0606-12/12 sanyo semiconductor co.,ltd. assumes no responsib ility for equipment failures that result from using products at values that exceed, even momentarily, rate d values (such as maximum ra tings, operating condition ranges, or other parameters) listed in products specif ications of any and all sanyo semiconductor co.,ltd. products described or contained herein. sanyo semiconductor co.,ltd. strives to supply high-qual ity high-reliability products, however, any and all semiconductor products fail or malfunction with some probabi lity. it is possible that these probabilistic failures or malfunction could give rise to acci dents or events that could endanger human lives, trouble that could give rise to smoke or fire, or accidents that could cause dam age to other property. when designing equipment, adopt safety measures so that these kinds of accidents or e vents cannot occur. such measures include but are not limited to protective circuits and error prevention c ircuits for safe design, redundant design, and structural design. upon using the technical information or products descri bed herein, neither warranty nor license shall be granted with regard to intellectual property rights or any other rights of sanyo semiconductor co.,ltd. or any third party. sanyo semiconductor co.,ltd. shall not be liable f or any claim or suits with regard to a third party's intellctual property rights which has resulted from the use of the technical information and products mentioned above. information (including circuit diagr ams and circuit parameters) herein is for example only; it is not guaranteed for volume production. any and all information described or contained herein are subject to change without notice due to product/technology improvement, etc. when designing equi pment, refer to the "delivery specification" for the sanyo semiconductor co.,ltd. product that you intend to use. in the event that any or all sanyo semiconductor c o.,ltd. products described or contained herein are controlled under any of applicable local export control laws and regulations, such products may require the export license from the authorities conc erned in accordance with the above law. no part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, or any in formation storage or retrieval system, or otherwise, without the prior written consent of sanyo semiconductor co.,ltd. ps this catalog provides information as of september, 2010. specifications and information herein are subject to change without notice.

▲Up To Search▲

Price & Availability of LB11693JH10

	To Download LB11693JH10 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .